Product Description

Roll to Roll Heat transfer machine  for garment 

Main Technical Data

Type:       DBX -1700      Rated voltage: 3-Phase A/C

Frequency:  60HZ           Heating method: heat transfer by oil

Rated power: heating body: 12kw, power system:0.55kw

Belt size: 1.75m（w）×2.48m（Perimeter ）

Equipment net size: 2.26m（L）×0.7m（W）×1.35m（H）

Net weight:  Approx.635kg      Noise level:  30dB

 

Note: The above data shall be based on actual equipment and please forgive us for not informing separately in case of any amendments.

Installation

1、After unpacking the package, please check whether the screws at various locations of the equipment are loosened during the transportation, if so, please tighten the screws.

2、The net weight of DBX-1700 type digital printing equipment is about 635kgs and the equipment shall be installed on flat surface with enough loading bearing capacity;

3、The equipment shall be operated in ventilated and dry environment with no corrosive gases; it is not allowed to place explosive and inflammable objects around the equipment;

4、Warning: the equipment shall have excellent earthing connection prior to operation to avoid electric shock;

5、Connect the power lines with corresponding diameters as per the rated power; use the standard 82 copper core cables or electric cables;

1． Wiring diagram as following:

 

Performance Sketch

 

 

1、Heating tube – provide heating energy for transfer printing;

2、Used for paper loading at the time of lower material input; or used as platform interface at the time of upper material input;

3、Working platform – carrier of transfer paper and material

4、Paper loader – for loading transfer paper

5、Fabric loader – for loading roll type or long fabric;

6、Hand wheel of detached device –

7、the belt may be detached or reset while in rotation.

 

Control Panel Instruction

 

         VFC（Variable Frequency Control） panel 

1, temperature control--- TO control and adjustthe temperature

2, VFC(Variable frequency control panel—to adjust and operate the mainframe's speed and direction

3, overall power button--- open or shut off the power
4, warm up button—to open or shut off the heater's power
5, transducer starting button—to start or stop the transducer
5、 rolling fabric's timing button6、.to adjust the rolling fabrics speed
7、changing direction button—to change the roller's direction

 

Notes:

 [the operation of VFC controller refers to the operation manual of VFC controller]

Operation Method

1．   After confirming the good earthing and correct power wiring of the system, set the breaker inside the case at on position, then press the button for “general power”,  then press the “VFC Run” key on the VFC panel and adjust the frequency to the suitable position;

2．   Press “heating” key to set the required temperature; which shall be decided according to different fabrics of the customer. We propose that the user shall make trial use by small size fabric and transfer paper when reaching the specified temperature and make corresponding adjustment in case of over high or over low temperature to ensure the quality of final product;

3．   Put the fabrics and transfer paper on the fabric holder and paper holder on the working table; when the temperature reaches the level for transfer printing, put the fabrics on the table and lower down the press roller and let the fabrics enter the roller. Note: the side of the transfer paper with ink shall face the fabrics and shall be placed over the fabrics;

4．   During the transfer printing process, the user may adjust the temperature in accordance with the color of the printed pattern, or adjust the temperature by controlling the speed of the tube.

5．   Upon completion of the printing work, press “cooling down” key and turn the hand wheel to remove the belt from roller; and the heating is stopped, when the temperature decreases to 80℃, the equipment will be automatically stopped.

Cautions

The deviation of belt in the left or right direction is normal due to the impact from uneven floor; so adjusting hole for belt deviation is provided at the back of the machine, which will tighten the belt at the right end if the belt deviates to the right direction; whereas to loosen the belt. The specific procedures are as following:

Insert the provided special hexagon spanner into the end of the adjusting pole of the adjusting hole below the right part and turn it. Please be noted that the clockwise turning is for loosening and the anti-clockwise turning is for tightening; the adjustment of the belt may not be finished within short time, so patience is necessary;

1、As the equipment is heating machinery, there may be certain noises from the roller, heating b body or big/small bearings during the operation process, which is the normal phenomenon and you may not worry about it;

2、The control circuit plate and the transducer inside the machine case shall be kept clean regularly with no dust or any other metal products fallen inside. Please do not open the protection cover to avoid electric shock;

3、The heating body, speed reducer and heat transfer oil etc of our company shall be used for any replacement and please do not replace or rectify the equipment without our permission.

4、The external surfaces of heating tube are specially treated and do not use the corrosive liquid to clean it or put hard object inside to scratch the surfaces.

 

Maintenance and Troubleshooting

Faults	Causes	Solutions
Temperature fails to rise	Insufficient voltage or the diameter of incoming lines over small	Increase the voltage or change with big diameter lines
	Phase loss; incoming lines or main cables disconnected or loosened	Check the electric lines
	One or more heating tubes damaged or wiring terminals loosened	Replace the heating tube
	Heating body aging ( this fault is impossible for new machine)	Replace the heating tube
Temperature out of control	Solid state relay breakdown	Replace
	Temperature control gauge damaged	Replace
Tube fails to rotate	Belt too loose	Tighten the belt
	Chain wheel in slippery	Tighten the screws
	Bearing blocked	Replace the bearing
	Transducer in failure	Replace
	Motor or speed reducer in failure	Replace

 

1.size:170cm
2.transfer speed:150-200M/Hour

3.time range:0-999sec.

 

Description:

 

 

Features:

1.The most advanced technology and imported units arew adopted by machine controlling system with automatic positioning , accuracy together with security ,electronic constant temperature controlling wtih high accuracy, long service life and other features

 

2.Heating wheel is controlled by sealed and heat-oil heating to efficiently ensure the even and stable temperature,

 

3. Printing speed is equipped with continuous speed adjustment system ,feeding equipment is convenient for operation ith swiftness and high reliablity.

 

4 Equipped with continuous speed adjustment system,you can adjust printing speed as you need ,The roller was heating up with oil and temperature heating system.

 

5. Get CE Certificate , one year warranty

 

The commodity in detail introduced

1. The wool blanket is separated from the type, uses US to import "Dupont" the raw material

2. The large capacity heat conduction oil, the constant temperature effect is good, continuously transfers India

3. The diameter 420 big drums, transfer the India speed to be quick

4. Frequency changer velocity modulation, frequency conversion velocity modulation electrical machinery

5. The carbon brush electric conduction heats up

6. Automatically puts the paper, the cloth and receives the paper, the cloth

 

●large size bearings, auto heating system of the easily wore parts that is convenient to maintain.

●The material of felt is adopted that from dubang USA.

●The material of the transmission roller is adopted Japan made

●Deploying alternative power supply system according to requirement, to replace the imitating imported felt separating structure, to avoid the defects that resulted from manual felt-adjusting.

 1、Main characteristic

Oil heat-transferring structure, colour evenness for trans-printing, individual production and production in batch are available. 

2、Technical  datasheet

Working power supply: 380V; fixed power efficiency: 10.5kw ; around 200 ℃; adjustable feed limit 0-2.5 meter/min

3、applicable production
Garment fabric cutting, e.g. swimming suit, sports suit, printing of the textile size, fabric in batch production.

Payment terms:                        
T/T,  Western Union, paypal                        

Shipping:                        
1.We have cooperated with Express Company, so our customers can get low freight cost.            

            
2. If you have your own forwarder in China, we can offer Free Delivery for you in Guangzhou City!        

                
3..There are no shipments on weekend and public holidays.                        

Package & delivery:                        
1. Neutral package or as customers' request.                        
2. we will arrange delivery 2-3workdays after we confirm the payment.                    

Company profile:
Our main business is : heat transfer paper, sublimation ink, heat transfer printer heat press machine       

heat transfer vinyl , Roll large format heat press machine,dark& light transfer paper for cotton T-shirt     Eco 

solvent paper,Printable heat transfer vinyl, digital printing manufacture.

 

 

Payment Terms︰ Western Union /T/T

Product Image